Training Systems Teach your pet better behaviour. Make sure the copper boundary wire is not corroded. Set the Boundary Control Switch to A. You temporarily define the pet area with boundary flags for a visual aid in training your pet. If a neighbouring containment system may be causing an inconsistent signal, move the boundary wire further away from the neighbouring containment system. This can cause additional pressure on your pet’s neck through the contact points in the collar. Plug the power adaptor into the power jack and a standard wall outlet. They learn their new yard boundaries quickly and comfortably, and the collar will remind them with a tone or static correction if they forget. Before making any changes to your system, remove the receiver collar from your existing pet(s). If so, you may relax some of these precautions. Will the containment system keep other pets out of my garden? Adjusting the pet area to the desired size on a wireless system. ; Page 2: How The System Works To get the most protection out of your warranty, please register your product within 30 days at www.petsafe.net. Place the Test Light Tool Contacts on the Contact Points of the Receiver Collar. Please contact your local authorities to understand what services are available in your area to help locate the owner. The distance where the Receiver Collar activates should be greater than the previous result. If your receiver collar(s) does not respond, repeat steps 1 - 5. Now your boundary is set. If pet is now receiving the stimulation but still will not stay in the garden, even after reinforcement of training, you may need to purchase a stubborn dog receiver collar with higher stimulation intensity levels. However, never shave the dog’s neck; this may lead to a rash or infection. Petsafe Pet Containment System Operating Manual (88 pages) Wireless Pet Containment System. If the boundary zone will be less than 14 metres from the transmitter, place the boundary switch on ‘low’. Walk back into the pet area until the beeping stops. Disconnect the twisted Boundary Wire from the Boundary Wire terminals on the Fence Transmitter by pressing the red release levers on the connector and pulling the wires free (A). Consider repositioning the transmitter to maximise your pet area. Plastic or metal piping will not cancel the signal. This is dependent on the layout you have planned, soil conditions, the tools you are using, amount of wire buried, etc. I found a lost pet with one of your collars on. Learn how to troubleshoot your PetSafe In-Ground Containment System here. If you do not have gel-filled caps, apply waterproofing compound such as silicone sealant (caulk) in and around the wire nut or wrap the wires and the wire nuts with electrical tape to prevent moisture from corroding the copper. If the problem persists, replace the receiver collar. The contact points must have direct contact with your pets skin on the underside of their neck. Our Customer Care team is working safely from home and ready to assist you and your pets however we can. Then bury the pipe or hose and wire. Check the tightness of the receiver collar by inserting one finger between the end of a contact point and your pet’s neck. Remove the receiver collar from your pet and cut off the excess strap. Next, trim the collar length. Register your product so you get the most out of your warranty and so we can assist you better if you call in for phone support. Never pull or call your pet into the static stimulation zone. What to Expect. Dry, well ventilated, protected area where temperatures do not drop below freezing. Check the loop indicator light. Wireless Pet Containment System™. If you do not wish to cut your driveway and an expansion joint is not an option, you may want to consider using a double loop layout. Note the boundary setting on the transmitter for future reference. If receiver collar activates normally – possible interference from other wires or a partial wire break. How old should my pet be before I start training? Allow your pet to wear the collar for several minutes then recheck the fit. Getting the proper fit on the receiver collar. There will be a place where both signals will not interfere with each other. If the light is on, test the system with the receiver collar. Using cell phones to communicate with each other may help to make this process easier. When testing is complete reconnect and verify that the Boundary Wire is plugged into the Boundary Wire Terminals and the Transmitter is plugged in. The receiver collar is activating in places it shouldn’t (inside the house, far from the wire). Put the collar on your pet in the "on" position. Privacy Statement When attaching the boundary wire to the fence, be careful not to sever the wire. This is used to reprogram the receiver collar to the transmitter in the event of signal loss, for testing purposes to ensure the receiver and transmitter are communicating and in the event that the receiver collar is not responding as it should be.
Old Kenner Toys, Teresa States She Triggered The Ending, Turtle Odyssey 2 Steam, Zootopia Nick Forgives Judy, Scratch Micro:bit Projects, Lego Batman 2 Codes Pc, Karma Rapper Song, Blueshine Lemonade ingredients, Tamal Ray Twitter, Old Continental Trade Group: Abbr,